Fortinet FortiGate ASM-CX4 Bedienungsanleitung PDF herunterladen

Products mentioned in this document are trademarks or registered trade-

marks of their respective holders.

Regulatory Compliance

FCC Class A Part 15 CSA/CUS

20 January 2009

QuickStart Guide

Package Contents

Installing the AMC Module

Connecting the Module

When properly inserted into the FortiGate unit, the interfaces of the ASM-CX4 appear in the

interface list by going to System > Network > Interface.

You can add policies, zones and so on as you would with other FortiGate interfaces.

Enable the bridging feature of the module using the Command Line Interface.

CLI Commands

To enable or disable bypass mode, press the Bypass FortiGate button, or use the following

CLI commands. For more information on these commands go to htp://kc.fortinet.com.

exec amc bypass-mode <enable | disable>

ASM-CX4

1 2 3 4

FG ACT

BYPASS

FORTIGATE

OOS

IPM

BYPASS

Tools and Documenation

FortiGate-30B

Trademarks

QuickStart Guide

ASM-CX4

1 2 3 4

FG ACT

BYPASS

FORTIGATE

OOS

IPM

BYPASS

ASM-CX4

1 2 3 4

FG ACT

BYPASS

FORTIGATE

OOS

IPM

BYPASS

It is important to carefully seat the FortiGate ASM-CX4 module all the way into the chassis.

Only then will the FortiGate ASM-CX4 module power-on.

To complete this procedure, you need:

• A FortiGate ASM-CX4 module.

• A FortiGate chassis with an empty AMC single-width (SW) opening.

• To avoid any electrostatic discharge, install in a static free area.

FortiGate ASM-CX4 modules are not hot swappable. The procedure for inserting the

FortiGate ASM-CX4 module into a FortiGate chassis slot requires the FortiGate unit to be

powered off.

To avoid any electrostatic discharge (ESD) when handling FortiGate ASM-CX4 modules,

install in a static free area.

To insert a FortiGate ASM-CX4 module into a FortiGate chassis

Ensure the FortiGate unit is powered off before proceeding.1.

Remove the panel block on the FortiGate unit using the hot swap latch.2.

Pull the latch on the ASM-CX4 module to the extended position.3.

Insert the ASM-CX4 module into the empty slot in the chassis. Ensure the Fortinet logo 4.

is right-side up. It should be on the lower-right corner of the module.

Carefully guide the module into the chassis.5.

Insert the module by applying moderate force to the front faceplate near the upper edge 6.

to slide the module into the slot.

01-30006-0474-20090120

Connector Type Speed Protocol Description

Ports 1 to 4 RJ-45 10/100/1000 Base-T Ethernet Copper network connections.

The module should glide smoothly into the chassis. If you encounter any resistance while

sliding the module in, the module could be aligned incorrectly. Pull the module back out

and try inserting it again.

Press the hot swap latch to lock in the module.7.

Power on the FortiGate unit. 8. The hot swap (HS) LED turns on and then begins ashing.

ASM-CX4 module ports

SWx/1 IP: ____.____.____.____ SWx/3 IP: ____.____.____.____

Netmask: ____.____.____.____ Netmask: ____.____.____.____

SWx/2 IP: ____.____.____.____ SWx/4 IP: ____.____.____.____

Netmask: ____.____.____.____ Netmask: ____.____.____.____

Removing the AMC module

Should you need to remove the ASM-CX4, shut down the FortiGate unit using proper shut

down procedures.

To remove the ASM-CX4 module

Ensure the FortiGate unit is powered off before proceeding.1.

To avoid any electrostatic discharge (ESD) when handling ASM-CX4 module, install in a 2.

static free area.

Pull the hot swap latch on the right-hand side of the module to the extended position to 3.

unlock the module from the FortiGate unit.

Gently pull the hot swap latch to remove the module.4.

FortiGate ASM-CX4

LED State Description

FGT ACT

Green The module is properly inserted in the FortiGate unit.

Off The module is not receiving power from the FortiGate unit.

Blue Ejection latch open. The module is ready for removal.

Flashing Ejection latch opened during system operation.

OOS LED currently not in use.

IPM

Green The module is properly inserted in the FortiGate unit.

Off The module is not receiving power from the FortiGate unit.

Port 1 to 4

(Right LED)

Off Connection at 10 Mb/s.

Amber Connection at 100 Mb/s.

Green Connection at 1000 Mb/s

Port 1 to 4

(Left LED)

Green Ethernet cable connected to the port and the FortiGate unit is on.

Flashing Green Network activity at this interface.

BYPASS

Green Bypass network activity at this interface.

Off Normal status or not receiving power from the FortiGate unit.

Visit these links for more information and documentation for your Fortinet product.

Technical Documentation - • http://docs.forticare.com

Fortinet Knowledge Center - • http://kc.forticare.com

Fortinet Technical Support - • http://support.fortinet.com

Inhaltsverzeichnis

Seite 1 - Connecting the Module

Kommentare zu diesen Handbüchern

Keine Kommentare

Fortinet FortiGate ASM-CX4 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Fortinet FortiGate ASM-CX4 herunter. Fortinet FortiGate ASM-CX4 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Fortinet FortiGate ASM-CX4