Fortinet MR1 Bedienungsanleitung Seite 118
- Seite / 640
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
118
5.2.7.4 storm-control unicast
This command enables unicast storm recovery mode on the selected interface.
Syntax
storm-control unicast
no storm-control unicast
no - This command disables unicast storm recovery mode on the selected interface.
Default Setting
None
Command Mode
Interface Config
This command enables unicast storm recovery mode on all interfaces.
Syntax
storm-control unicast
no storm-control unicast
no - This command disables unicast storm recovery mode on all interfaces.
Default Setting
None
Command Mode
Global Config
- FortiSwitch-100 1
- Table of Contents 3
- 1 Introduction 23
- 1.3 Front-Panel Components 25
- 1.4 LED Indicators 25
- 1.5 Rear Panel Description 25
- 1.6 Management Options 26
- 1.9 SNMP-Based Management 26
- 2.1 Package Contents 28
- 2.2 Switch Installation 28
- 2.4 System Information Setup 30
- Out-of-Band PC (Only XMODEM) 33
- 3.1 Overview 41
- 3.2 How to log in 41
- Main Menus 42
- 4.1 CLI Command Format 46
- 4.2 CLI Mode-based Topology 46
- Conventions 47
- 5 Switching Commands 49
- 5.1.3 show eventlog 50
- 5.1.4 show running-config 51
- 5.1.5 show sysinfo 51
- 5.1.6 show hardware 52
- 5.1.7 show loginsession 53
- 5.2.1 Interface 53
- 5.2.1.4 interface 60
- 5.2.1.5 speed-duplex 60
- 5.2.1.6 negotiate 61
- 5.2.1.7 capabilities 62
- 5.2.1.9 shutdown 64
- Database Tables 66
- 5.2.3 VLAN Management 70
- 5.2.3.2 show vlan id 71
- 5.2.3.3 show protocol group 72
- 5.2.3.5 vlan database 73
- 5.2.3.6 vlan 73
- 5.2.3.7 vlan name 74
- 5.2.3.8 vlan makestatic 75
- 5.2.3.9 protocol group 75
- 5.2.3.14 switchport tagging 80
- 5.2.3.15 switchport priority 81
- 5.2.4.1 show bridge-ext 85
- 5.2.4.5 bridge-ext gvrp 88
- 5.2.4.6 bridge-ext gmrp 89
- 5.2.4.7 switchport gvrp 89
- 5.2.4.8 switchport gmrp 90
- 5.2.4.9 garp timer 91
- 5.2.5 IGMP Snooping 95
- 5.2.6 Port Channel 107
- 5.2.6.2 port-channel 108
- 5.2.6.4 staticcapability 109
- 5.2.6.6 port-channel name 110
- 5.2.6.7 adminmode 111
- 5.2.6.8 lacp 111
- 5.2.6.9 channel-group 112
- 5.2.7 Storm Control 114
- 5.2.8 L2 Priority 122
- 5.2.9 Port Mirror 123
- 5.2.9.2 port-monitor session 124
- 5.3 Management Commands 125
- 5.3.1.2 show ip filter 126
- 5.3.1.3 show ip ipv6 127
- 5.3.1.4 mtu 127
- 5.3.1.5 interface vlan 128
- 5.3.1.6 ip address 128
- 5.3.1.7 ip default-gateway 129
- 5.3.1.8 ip address protocol 129
- 5.3.1.9 ip filter 130
- 5.3.1.10 ip ipv6 131
- 5.3.2.1 show line console 132
- 5.3.2.2 line console 132
- 5.3.2.3 baudrate 133
- 5.3.2.4 exec-timeout 133
- 5.3.2.5 password-threshold 134
- 5.3.2.6 silent-time 134
- 5.3.3.1 telnet 135
- 5.3.3.2 show line vty 135
- 5.3.3.3 line vty 136
- 5.3.3.4 exec-timeout 137
- 5.3.3.5 password-threshold 137
- 5.3.3.6 maxsessions 138
- 5.3.3.7 sessions 138
- 5.3.3.8 telnet sessions 139
- 5.3.3.9 telnet maxsessions 139
- 5.3.3.10 telnet exec-timeout 140
- 5.3.4 SNMP Server Commands 141
- 5.3.4.2 show trapflags 142
- 5.3.4.3 snmp-server sysname 143
- 5.3.4.4 snmp-server location 143
- 5.3.4.5 snmp-server contact 144
- 5.3.4.7 snmp-server host 147
- 5.3.5 SNMP Trap Commands 151
- 5.3.5.4 snmptrap ipaddr 153
- 5.3.6 HTTP commands 154
- 5.3.6.2 ip javamode 155
- 5.3.6.3 ip http port 155
- 5.3.6.4 ip http server 156
- 5.3.6.5 ip http secure-port 157
- 5.3.7.1 show ip ssh 158
- 5.3.7.2 ip ssh 159
- 5.3.7.3 ip ssh protocol 159
- 5.3.7.4 ip ssh maxsessions 160
- 5.3.7.5 ip ssh timeout 160
- 5.3.8 DHCP Client Commands 161
- 5.3.9 DHCP Relay Commands 162
- 5.4 Spanning Tree Commands 164
- 5.4.2 Configuration Commands 171
- 5.4.2.4 spanning-tree mode 173
- 5.4.2.9 spanning-tree mst 176
- 5.5.1 Show Commands 181
- 5.5.2 show logging buffered 182
- 5.5.3 show logging traplog 182
- 5.5.3.1 show logging hosts 183
- 5.5.4 Configuration Commands 184
- 5.5.4.2 logging console 185
- 5.5.4.3 logging host 185
- 5.5.4.4 logging syslog 187
- 5.6.1 script apply 188
- 5.6.2 script delete 189
- 5.6.3 script list 189
- 5.6.4 script show 190
- 5.7.1 Show Commands 190
- 5.7.2 Configuration Commands 191
- 5.8 Security Commands 193
- 5.8.1.2 show authentication 194
- 5.8.1.4 show dot1x 195
- 5.8.1.5 show dot1x detail 196
- 5.8.1.7 show dot1x summary 198
- 5.8.1.8 show dot1x users 198
- 5.8.1.9 show radius-servers 199
- 5.8.1.10 show radius 199
- 5.8.1.13 show tacacs 202
- 5.8.1.14 show port-security 203
- 5.8.2 Configuration Commands 205
- 5.8.2.3 username login 207
- 5.8.3.1 dot1x initialize 208
- 5.8.3.2 dot1x default-login 208
- 5.8.3.3 dot1x login 209
- 5.8.3.5 dot1x user 210
- 5.8.3.6 dot1x port-control 210
- 5.8.3.7 dot1x max-req 212
- 5.8.3.10 dot1x timeout 213
- 5.8.4.2 radius-server host 215
- 5.8.4.3 radius-sever key 216
- 5.8.5.1 tacacs 219
- 5.8.5.2 tacacs mode 219
- 5.8.5.3 tacacs server-ip 220
- 5.8.5.4 tacacs port 220
- 5.8.5.5 tacacs key 221
- 5.8.5.6 tacacs retry 221
- 5.8.5.7 tacacs timeout 222
- 5.8.6.1 port-security 222
- Commands 225
- 5.9.1.2 show cdp neighbors 226
- 5.9.2 Configuration Commands 227
- 5.9.2.2 cdp run 228
- 5.9.2.3 cdp timer 229
- 5.9.2.4 cdp holdtime 229
- 5.10.2.2 sntp client mode 232
- 5.10.2.3 sntp client port 233
- 5.10.2.7 sntp server 235
- 5.11 System Utilities 236
- 5.11.1.2 clear traplog 237
- 5.11.1.3 clear eventlog 237
- 5.11.1.5 clear config 238
- 5.11.1.6 clear pass 239
- 5.11.1.7 clear counters 239
- 5.11.1.8 clear dns counter 239
- 5.11.1.9 clear dns cache 240
- 5.11.1.10 clear cdp 240
- 5.11.1.11 clear vlan 241
- 5.11.1.12 enable passwd 241
- 5.11.1.14 clear port-channel 242
- 5.11.1.15 clear ip filter 242
- 5.11.2 copy 244
- 5.11.3 delete 247
- 5.11.4 dir 247
- 5.11.5 whichboot 248
- 5.11.6 boot-system 249
- 5.11.7 ping 249
- 5.11.8 traceroute 250
- 5.11.9 logging cli-command 251
- 5.11.10 calendar set 251
- 5.11.11 reload 252
- 5.11.12 configure 252
- 5.11.13 disconnect 253
- 5.11.14 hostname 253
- 5.11.15 quit 254
- 5.12.1 General Commands 255
- 5.12.2 Class Commands 256
- 5.12.2.1 class-map 257
- 5.12.2.2 no class-map 257
- 5.12.2.3 class-map rename 258
- 5.12.2.4 match any 258
- 5.12.2.5 match class-map 259
- 5.12.2.6 no match class-map 259
- 5.12.2.7 match dstip 260
- 5.12.2.8 match dstl4port 260
- 5.12.2.9 match ip dscp 261
- 5.12.2.11 match ip tos 262
- 5.12.2.12 match protocol 263
- 5.12.2.13 match srcip 263
- 5.12.2.14 match srcl4port 264
- 5.12.3 Policy Commands 265
- 5.12.3.2 drop 266
- 5.12.3.3 redirect 266
- 5.12.3.4 conform-color 267
- 5.12.3.5 mark cos 267
- 5.12.3.6 class 268
- 5.12.3.7 no class 268
- 5.12.3.8 mark ip-dscp 268
- 5.12.3.9 mark ip-precedence 269
- 5.12.3.10 police-simple 269
- 5.12.3.11 policy-map 270
- 5.12.3.12 policy-map rename 270
- 5.12.4 Service Commands 271
- 5.12.5 Show Commands 272
- 5.12.5.1 show class-map 273
- 5.12.5.2 show diffserv 274
- 5.12.5.3 show policy-map 275
- 5.12.5.7 show service-policy 279
- 5.13 ACL Command 281
- 5.13.2.3 mac access-list 285
- 5.13.2.4 mac access-group in 286
- 5.13.2.5 access-list 287
- 5.13.2.6 no access-list 287
- 5.14.1 Show Commands 288
- 5.14.1.3 show queue trust 290
- 5.14.2.1 queue cos-map 292
- 5.14.2.3 queue trust 294
- 6 Routing Commands 299
- Step 1: Create Two VLANs 300
- 6.1.1.3 show ip arp static 303
- 6.1.2 Configuration Commands 304
- 6.1.2.3 arp cachesize 305
- 6.1.2.4 arp dynamicrenew 305
- 6.1.2.5 arp purge 305
- 6.1.2.6 arp resptime 306
- 6.1.2.7 arp retries 306
- 6.2 IP Routing Commands 307
- 6.2.1.4 show ip route 309
- 6.2.1.6 show ip route entry 310
- 6.2.1.8 show ip traffic 312
- 6.2.2.1 routing 312
- 6.2.2.2 ip routing 313
- 6.2.2.3 ip address 313
- 6.2.2.4 ip route 313
- 6.2.2.7 ip forwarding 315
- 6.2.2.9 ip mtu 316
- 6.2.2.10 encapsulation 316
- 6.3.1.2 show ip ospf area 318
- 6.3.1.9 show ip ospf range 323
- 6.3.2 Configuration Commands 326
- 6.3.2.3 ip ospf 327
- 6.3.2.4 1583compatibility 327
- 6.3.2.5 area default-cost 328
- 6.3.2.6 area nssa 328
- 6.3.2.9 area nssa no-summary 330
- 6.3.2.12 area range 331
- 6.3.2.13 area stub 332
- 6.3.2.21 default-metric 336
- 6.3.2.22 distance ospf 337
- 6.3.2.26 ip ospf areaid 339
- 6.3.2.28 ip ospf cost 340
- 6.3.2.34 ip ospf mtu-ignore 344
- 6.3.2.35 router-id 345
- 6.3.2.36 redistribute 345
- 6.4.1 show bootpdhcprelay 346
- 6.4.3 bootpdhcprelay enable 347
- 6.4.7 ip dhcp restart 349
- 6.5.1 Show Commands 350
- 6.5.1.3 show dns cache 351
- 6.5.2 Configuration Commands 352
- 6.5.2.3 ip domain-name 353
- 6.5.2.4 ip domain-list 353
- 6.5.2.5 ip name-server 354
- 6.5.2.6 ip domain-lookup 354
- 6.5.2.7 clear domain-list 355
- 6.5.2.8 clear dns 355
- 6.5.2.9 clear dns cache 356
- 6.5.2.10 clear dns counter 356
- 6.6.2 Configuration Commands 359
- 6.6.2.2 ip rip 360
- 6.6.2.3 auto-summary 360
- 6.6.2.5 default-metric 361
- 6.6.2.6 distance rip 362
- 6.6.2.7 hostrouteaccept 362
- 6.6.2.8 split-horizon 363
- 6.6.2.9 distribute-list 363
- 6.6.2.10 redistribute 364
- 6.7.1 show ip irdp 366
- 6.7.2 ip irdp 367
- 6.7.3 ip irdp broadcast 368
- 6.7.4 ip irdp holdtime 368
- 6.8 VLAN Routing Commands 370
- (VRRP) Commands 371
- 6.9.1.2 show ip vrrp brief 372
- 6.9.2 Configuration Commands 374
- 6.9.2.2 ip vrrp ip 375
- 6.9.2.3 ip vrrp mode 375
- 6.9.2.5 ip vrrp preempt 376
- 6.9.2.6 ip vrrp priority 377
- 7 IP Multicast Commands 380
- 7.1.1.5 show ip dvmrp prune 382
- 7.1.1.6 show ip dvmrp route 383
- 7.1.2 Configuration Commands 384
- 7.2.1 Show Commands 385
- 7.2.2 Configuration Commands 389
- 7.2.2.7 ip igmp robustness 392
- 7.3 Multicast Commands 393
- 7.3.1.4 show ip mcast mroute 395
- 7.3.1.5 show mrinfo 398
- 7.3.1.6 show mstat 399
- 7.3.1.7 show mtrace 399
- 7.3.2 Configuration Commands 400
- 7.3.2.3 no ip mcast mroute 401
- 7.3.2.4 ip mcast boundary 402
- 7.3.2.6 mrinfo 403
- 7.3.2.7 mstat 404
- 7.3.2.8 mtrace 405
- Mode (PIM-DM) Commands 406
- 7.4.2 Configuration Commands 408
- 7.4.2.2 ip pimdm mode 409
- Mode (PIM-SM) Commands 410
- 7.5.1.6 show ip pimsm rp 413
- 7.5.1.7 show ip pimsm rphash 414
- 7.5.2 Configuration Commands 415
- 7.5.2.5 ip pimsm staticrp 417
- 7.5.2.6 ip pimsm mode 418
- 8.1 Overview 423
- 8.2 Main Menu 424
- Configuring Serial Port Page 431
- Defining User Accounts Page 432
- Viewing Login Session Page 435
- Defining User Login Page 436
- 8.2.1.5 Viewing Logs 439
- Viewing Buffered Log Page 440
- Configuring Console Log Page 441
- Viewing Event Log Page 442
- 8.2.1.7 Defining SNMP 449
- 8.2.1.8 Viewing Statistics 453
- Resetting the Switch Page 464
- Removing Specific File Page 467
- Defining Ping Function Page 468
- Managing CDP Function 469
- Configuring Trap Flags Page 472
- Viewing Trap Log Page 473
- 8.2.1.11 Configuring SNTP 474
- Configuring SNTP Server Page 476
- 8.2.2 Switching Menu 481
- 8.2.2.3 Defining GARP 488
- Viewing GMRP MFDB Table Page 503
- 8.2.3 Routing Menu 516
- Configuring ARP Table 517
- Configuring IP 519
- Viewing IP Statistics 520
- 523
- Configuring IP Interfaces 524
- 8.2.3.3 Managing OSPF 525
- Configuring OSPF 525
- Configuring Area 527
- Configuring Area Range 530
- View Interface Statistics 531
- Configuring OSPF Interface 533
- Configuring OSPF Neighbor 537
- 8.2.3.5 Managing DNS Relay 548
- Configuring DNS Relay 548
- Configuring Domain Name 549
- Configuring Name Server 550
- Configuring DNS Host 551
- Viewing Router Route Table 560
- Configuring VLAN Routing 565
- 8.2.3.10 Managing VRRP 567
- Configuring VRRP 567
- Configuring Virtual Router 567
- 8.2.4 Security Menu 572
- 8.2.4.2 Managing RADIUS 581
- IP Filter Configuration Page 588
- 8.2.5 QOS Menu 591
- Configuring CoS interface 609
- 8.2.6 IP Multicast Menu 612
- Viewing DVMRP Prune Summary 617
- Viewing DVMRP Route Summary 617
- Configuring Mrinfo Run Page 629
- Viewing Mrinfo Summary Page 629
- Configuring Mstat Run Page 630
- Viewing Mstat Summary Page 631
- Configuring Mtrace Run Page 632
- Viewing Mtrace Summary Page 633
Verwandte Produkte und Handbücher für Vernetzung Fortinet MR1
Vernetzung Fortinet MR8 Bedienungsanleitung
(62 Seiten)
(62 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.156 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern